Açıklama

snmp3_set(
    string $hostname,
    string $security_name,
    string $security_level,
    string $auth_protocol,
    string $auth_passphrase,
    string $privacy_protocol,
    string $privacy_passphrase,
    array|string $object_id,
    array|string $type,
    array|string $value,
    int $timeout = -1,
    int $retries = -1
): bool

snmp3_set() is used to set the value of an SNMP object specified by the object_id.

Even if the security level does not use an auth or priv protocol/password valid values have to be specified.

Bağımsız Değişkenler

hostname

The hostname of the SNMP agent (server).

security_name

the security name, usually some kind of username

security_level

the security level (noAuthNoPriv|authNoPriv|authPriv)

auth_protocol

the authentication protocol (MD5 or SHA)

auth_passphrase

the authentication pass phrase

privacy_protocol

the privacy protocol (DES or AES)

privacy_passphrase

the privacy pass phrase

object_id

The SNMP object id.

type

MIB her nesne kimliğini türünü tanımlar. Aşağıdaki listeden tek bir karakter olarak belirtilmelidir.

**types**
=	Tür MIB'den alınır.
i	INTEGER
u	INTEGER
s	STRING
x	HEX STRING
d	DECIMAL STRING
n	NULLOBJ
o	OBJID
t	TIMETICKS
a	IPADDRESS
b	BITS

SNMP kütüphanesi derlenirken OPAQUE_SPECIAL_TYPES tanımlanmışsa aşağıdakiler de geçerlidir:

**types**
U	unsigned int64
I	signed int64
F	float
D	double

Most of these will use the obvious corresponding ASN.1 type. 's', 'x', 'd' and 'b' are all different ways of specifying an OCTET STRING value, and the 'u' unsigned type is also used for handling Gauge32 values.

If the MIB-Files are loaded by into the MIB Tree with "snmp_read_mib" or by specifying it in the libsnmp config, '=' may be used as the type parameter for all object ids as the type can then be automatically read from the MIB.

Note that there are two ways to set a variable of the type BITS like e.g. "SYNTAX BITS {telnet(0), ftp(1), http(2), icmp(3), snmp(4), ssh(5), https(6)}":

Using type "b" and a list of bit numbers. This method is not recommended since GET query for the same OID would return e.g. 0xF8.
Using type "x" and a hex number but without(!) the usual "0x" prefix.

See examples section for more details.

value

The new value

timeout

The number of microseconds until the first timeout.

retries

The number of times to retry if timeouts occur.

Dönen Değerler

Başarı durumunda true, başarısızlık durumunda false döner.

If the SNMP host rejects the data type, an E_WARNING message like "Warning: Error in packet. Reason: (badValue) The value given has the wrong type or length." is shown. If an unknown or invalid OID is specified the warning probably reads "Could not add variable".

Sürüm Bilgisi

Sürüm:	Açıklama
8.5.0	Now throws a ValueError when the hostname length is equal to or greater than 128 bytes, when the port is negative or greater than 65535, or when the timeout or retries values are lower than -1 or too large.

Örnekler

Örnek 1 Using snmp3_set()

<?php
  snmp3_set('localhost', 'james', 'authPriv', 'SHA', 'secret007', 'AES', 'secret007', 'IF-MIB::ifAlias.3', 's', "foo");
?>

Örnek 2 Using snmp3_set() for setting BITS SNMP object id

<?php
  snmp3_set('localhost', 'james', 'authPriv', 'SHA', 'secret007', 'AES', 'secret007', 'FOO-MIB::bar.42', 'b', '0 1 2 3 4');
// or
  snmp3_set('localhost', 'james', 'authPriv', 'SHA', 'secret007', 'AES', 'secret007', 'FOO-MIB::bar.42', 'x', 'F0');
?>